hssi_loopback - Software utility to run HSSI loopback tests on FPGA
hssi_loopback [[--bus|-b <bus number>] [--device | -d <device number>] [--function | -f <function number>]]|[--socket-id <socket-id>] [--mode|-m auto|e40|e10] [send [<source port> [<destination port>] [--packet-count|-c <count>] [--packet-delay|-d <delay>] [--packet-length|-l <length>]] |status [clear] | stop | readmacs
hssi_loopback utility works in conjunction with a packet
generator accelerator function unit (AFU) to test high-speed serial
interface (HSSI) cards. The
hssi_loopback utility tests both
external and internal loopbacks.
hssi_loopback runs an external
loopback test when the command line arguments include both source and
hssi_loopback runs an internal loopback test when
command line arguments include a single port.
runs on the Intel Xeon with Arria 10 FPGA. You cannot run it on the
Intel PAC (programmable accelerator card).
NOTE: The following limitations apply to the current version of hssi_loopback:
- For the external loopback the two port arguments can be the same. For the e10 design, the ports should be the same.
hssi_loopbacktest supports only the e40 and e10 E2E AFUs. The e10 E2E AFU tests HSSI with a retimer card.
hssi_loopbacktest uses the control and status registers (CSRs) defined in the AFU.
-S SOCKET_ID, --socket-id SOCKET_ID
Socket ID FPGA resource.
-B BUS, --bus BUS
Bus ID of FPGA resource.
-D DEVICE, --device DEVICE
Device ID of FPGA resource.
-F FUNCTION, --function FUNCTION
Function ID of FPGA resource.
Specifies guid for the AFC enumeration.
One of the following: [
auto is the
default and indicates that the software runs the mode based on the first
accelerator functional context (AFC) it enumerates.
Timeout (in seconds) before the application terminates in continuous mode. Continuous mode is the default when you do not specify the number of packets.
Delay (in seconds) between printing out a simple status line. Default is 0.100 seconds (100 milliseconds).
The number of packets to send.
The delay in between packets. This delay is the number of 100 MHz clock cycles, roughly 10 nanoseconds.
The packet size to send. The minimum is 46 bytes and the maximum is 1500 bytes. The default is 46 bytes.
send <source port> [<destination port>] [--packet-count|-c <count>] [--packet-delay|-d <delay>] [--packet-length|-l <length>]
Send packets from one port to the other. If the command line does not specify a destination port, the test runs an internal loopback. Otherwise, the test runs an external loopback from the source port to the destination port.
Read and interpret the status registers and print to the screen.
clear clears the status registers.
Issue a stop command to all Ethernet controllers in the AFU.
Read and display the port MAC addresses. An EEPROM stores the MAC addresses.
0 Success - Number of packets received are equal to the number of packets sent and no errors are reported.
-1 Loopback failure - Either number of packets does not match or the test detected errors.
-2 Errors parsing arguments.
Read the MAC addresses of the AFU loaded on bus 0x5e:
>sudo hssi_loopback readmacs -B 0x5e
Run an external loopback, sending 100 packets from port 0 to port 1. The AFU is on bus 0x5e:
>sudo hssi_loopback -B 0x5e send 0 1 -c 100
Run an internal loopback until a timeout of 5 seconds is reached. The AFU is on bus 0x5e:
>sudo hssi_loopback -B 0x5e send 0 -t 5
|Document Version||Intel Acceleration Stack Version||Changes|
|2018.05.21||1.1 Beta. (Supported with Intel Quartus Prime Pro Edition 17.1.)||Correcte d typos.|