Intel® Accelerator Functional Unit (AFU) Simulation Environment (ASE) User Guide

Intended Audience

The Accelerator Functional Unit (AFU) Accelerator Simulation Environment (ASE) User Guide addresses both beginning and experienced developers. To be successful, you should have knowledge and experience in the following areas:

  • C/C++
  • Verilog/SystemVerilog
  • RTL simulators such as Synopsys VCS-MX* or Mentor Graphics ModelSim-SE* or QuestaSim*

Alternatively, you can create a team that includes developers who specialize in either RTL or software development. Previous FPGA place and route (PAR) experience is not required to be successful, but PAR experience is also a useful skill.

Introduction

The ASE provides a consistent transaction-level hardware interface and software API that allows you to develop a production-quality Accelerated Functional Unit (AFU) and host software application. The ASE supports both the Intel Xeon® Processor with Integrated FPGA and the Intel Acceleration Stack for Intel Xeon CPU with FPGAs also called the Intel Programmable Acceleration Card (PAC). The figures in this user guide illustrate the Intel PAC with Arria® 10 GX FPGA. The figures show a local memory that is only available on the PAC.

To use the ASE Environment you must have source code in a language that RTL simulators can interpret. The following languages are possible:

  • Verilog
  • SystemVerilog
  • VHDL

Note

The ASE supports one AFU and one application at a time. The ASE does not support multiple-slot simulation.

Supported

AFU Simulation Environment (ASE) Overview

ASE is a dual-process simulator. One process runs an AFU RTL simulation. The other process connects to software that runs on the RTL AFU simulation. This unified simulation environment reduces AFU hardware and software development time. The OPAE software distribution includes the ASE.

Block

The ASE provides two interfaces:

  • Software: OPAE API implemented in the C programming language.
  • Hardware: Core Cache Interface (CCI-P) specification implemented in SystemVerilog.

Use these interfaces to deploy your IP on the Integrated FPGA Platform or the Intel PAC with Arria 10 GX FPGA.

ASE Capabilities

  • The ASE provides a protocol checker to ensure protocol correctness. The ASE also provides methods to identify potential issues early, before in-system deployment.
  • The ASE can help identify certain lock conditions and Configuration and Status Registers (CSR) address mapping and pointer math errors.
  • The ASE tracks memory requested from the accelerator. The memory model immediately flags illegal memory transactions to locations outside of requested memory spaces. Consequently, you can fix incorrect memory accesses early, during the simulation phase.
  • The ASE does not guarantee that you can synthesize an AFU. After you verify the AFU RTL functionality in the ASE, use the ASE and the Intel Quartus® Prime Pro Edition software iteratively to generate the Accelerator Function (AF).
  • The ASE provides a data hazard checker that identifies CCI-P traffic patterns that may cause Write After Write (WAW), Read After Write (RAW), and Write After Read (WAR) hazards. Debug these transactions using a waveform viewer or avoid them by using a relevant Memory Properties Factory (MPF) shim.
  • The ASE does not require administrator privileges. After installing all the required tools, you can run the ASE on a plain vanilla user Linux machine.

ASE Limitations

When using ASE in the application development cycle, consider the following limitations:

  • The ASE is a transaction-level simulator. It does not model either Intel UPI- or PCIe-specific packet structures and protocol layers.
  • The ASE does not simulate caching and is not a cache simulator. It cannot reliably simulate cache collisions or capacity issues.
  • Although ASE models some latency parameters, it cannot model real-time system-specific latency. It is also not an accurate timing simulation of the design or latency and bandwidth of the real system. The ASE models enable you to develop functionally correct accelerators.
  • The ASE does not simulate multi-AFU or multi-socket configurations.

ASE-Based AFU Design Workflow

ASE-based

AFU development using the ASE includes the following four stages:

  1. Learning/Training: Learn to use ASE and understand the interface specifications and platform. Review sample code to get an understanding of the CCI-P specification and OPAE API function calls. Run samples in an ASE simulation.

  2. Development Phase: Use the ASE to develop AFU RTL and software application in a single workflow. Develop RTL from the specification or by modifying existing sample RTL. The ASE includes a behavioral model of the FPGA Interface Manager (FIM) IP that provides immediate feedback on functionality during the development phase. The ASE flags errors in CCI-P protocols, transactions, and memory accesses. Consequently, you can fix these errors before moving to the time-consuming bitstream generation phase.

  3. Bitstream Generation: Once AFU RTL and software are functionally correct, open the AFU RTL in the Intel Quartus Prime Pro Edition software. Run the place and route (PAR) tools for your platform.

    Use the Synthesis reports to correct problems in the AFU RTL. Then, return to the development phase and revalidate in ASE. Bitstream generation can take hours depending on design complexity, area, and so on. After successful bitstream generation, perform timing analysis to check for timing corners, setup and hold violations, clock closure, and so on. After correcting failures found during timing analysis, revalidate in the ASE environment. When the AFU is error-free, generate the Accelerator Function (AF) bitstream that represents the AFU.

  4. In-system Deployment: Test the AF in system hardware. Use Signal Tap to debug problems. Develop platform-specific software optimizations.

Synthesize

The AFU RTL code and OPAE software code you create in the ASE is compatible with the Intel Quartus Prime PAR software if the following two conditions are true: * The AFU RTL code is synthesizable. * The AFU RTL code meets timing.

In the simulation environment, complete the following steps to create an AF bitstream and program the hardware: 1. Compile the AFU RTL in either the Synopsys VCS-MX or in the Mentor Graphics ModelSim-SE or QuestaSim simulators. 2. Compile the software application for an ASE-specific implementation of the OPAE API. 3. Synthesize the AFU RTL in the Intel Quartus Prime Pro software to generate a bitstream. 4. Program the hardware using this bitstream.

Note

The ASE only operates using the AFU RTL source code. It cannot take the AF bitstream as input.

System Requirements

The OPAE software release includes the ASE. The current OPAE ASE release supports both Acceleration Stack for the Intel Xeon Processor with Integrated FPGA and Acceleration Stack for the Intel PAC card.

The ASE is available only on 64-bit Linux operating systems with one of the following simulators: * 64-bit Synopsys* RTL Simulator (minimum version VCS-MX H2013.06-SP1) * 32 and 64-bit Mentor Graphics* Modelsim SE Simulator (minimum version 10.5a) * 64-bit Mentor Graphics* QuestaSim Simulator (minimum version 10.4d)

ASE performance is better on a 64-bit RTL simulator. Consult your RTL simulator vendor for Synopsys or Mentor Graphics for specific simulation requirements.

The ASE uses Inter-Process Communication (IPC) constructs. Under most circumstances these constructs operate without glitches. The following Linux locations should exist and be writeable. In most Linux distributions, /dev/shm comes pre-mounted as a default option.

Here are the other ASE requirements:

  • C-Compiler: gcc 4.8.5 or above

    * Boost Development libraries
    * UUID Development libraries
    * JSON Development libraries
    * Please see the dependencies of the OPAE System library build process
    
  • CMake: version 2.8.11 or above

  • GLIBC: version 2.19 or above

  • Python: version 2.7 or above

  • Intel Quartus Prime Pro Edition: The ASE must find the $QUARTUS_HOME/eda/sim_lib/ directory. You specify this directory during project definition in the Intel Quartus Prime Pro Edition software.

The ASE provides the env_check.sh bash script in the /sw/opae-x.x.x/ase/scripts directory. Run this script to verify the your installation.

Check the RTL simulator product information for supported operating systems, installation notes, and other related information. The RTL simulator must be able to perform the following functions:

  • Compilation of the SystemVerilog Direct Programming Interface (DPI) constructs
  • Compilation of the standard examples that are included in the installation
  • Support for SystemC

Package Description

Download the ASE as source or in RPM format.

The source directory tree is:

OPAE_BASEDIR
    |-- ase
    |   |-- api
    |   |   -- src
    |   |-- in
    |   |-- rtl
    |   |   -- dcp_emif_model
    |   |-- scripts
    |   |-- sw
    |
    |-- cmake
    |-- common
    |   |-- include
    |   |   |-- opae
    |   |   |--safe_string
    |
    |-- doc
    |-- libopae
    |-- libopaecxx
    |-- platforms
    |-- pyopae
    |-- safe_string
    |-- samples
    |-- scripts
    |-- tools

This directory tree shows the package structure of the ASE distribution. The following directories implement and run the ASE simulator:

  • ase: This is the ASE simulator implementation directory. It contains the following subdirectories: * api/src: This directory contains the OPAE Intel ASE implementation as a compiled library. You can link statically or dynamically to this library. * rtl: This directory contains the RTL components of the ASE. You can compile this RTL for either platform. * dcp_emif_model: This is the local DDR memory model for PAC card. Compile this model for PAC mode simulations. * scripts: This directory contains several useful scripts. Refer to the ASE Scripts Section for more information. * sw: This directory contains the software components of the ASE. All simulations require the software components. The GNU Compiler Collection (GCC) compiles these components.
  • common: This directory contains the OPAE library definitions. It defines various macros for access to an FPGA in an OPAE context.
  • libopae: This library is the Intel platform-specific implementation of the OPAE API.
  • platforms: This directory contains scripts and RTL to manage the connection between a platform and the AFU top-level interface.
  • scripts: This directory contains test build scripts.
  • tools: This directory contains the FPGA tools including the fpgadiag and fpgaconfig tools.

ASE Scripts

The ASE distribution under the ase/scripts includes several scripts. Use these scripts to initialize, set up, and clean an existing ASE simulation environment.

Simulation Tool Set Up

Use ase/scripts/ase_setup_template.sh as a template script to set up the required tools. This script has many empty placeholders for site- and environment-specific information. Consult your Electronic Design Automation (EDA) tools administrator, or the RTL simulator user guides for help setting up the tools.

ASE Environment Check

This script checks the status of the OS distribution, distro, and available system libraries. This check is a non-exhaustive. It looks for only the most important dependencies, such as the GCC version, GLIBC version, and so on.

$ ./ase/scripts/env_check.sh

AFU Simulation Using the ASE

Before configuring the ASE, follow the instructions for building the OPAE SDK and ensure that either the OPAE installed bin or the OPAE build tree bin directory is on your shell’s PATH.

To simulate an AFU, replicate the ASE source tree and add the AFU-specific configuration. The OPAE installation includes several scripts to accomplish this task. The primary script, afu_sim_setup, is in the OPAE bin directory.

Refer to the ASE Example section below for a sample workload definition and execution flow.

afu_sim_setup

The afu_sim_setup script reads a file containing a list of RTL sources (<rtl_sources.txt>) and configures a simulation environment for the specified sources. The afu_sim_setup command copies your base ASE environment to the <target dir>.

$ afu_sim_setup --sources=<rtl_sources.txt> <target dir>
  • The only required argument to the afu_sim_setup command is the directory for the new AFU environment. Here are the optional arguments:
  • --help The help argument lists all the arguments to afu_sim_setup.
  • --platform: The platformargument specifies any platform defined in the platform database, including both the Integrated FPGA Platform or the Intel PAC. This argument is generally not required when a hardware platform release is installed. In that case, the OPAE_PLATFORM_ROOT environment variable points to the hardware release, which defines the platform.

afu_sim_setup is a wrapper for the following scripts. You can also access both of these scripts directly:

  • rtl_src_config: This script transforms the list of RTL sources into simulator configuration files.
  • generate_ase_environment.py: This script instantiates your simulated platform configuration.

rtl_src_config

The /platforms/scripts/rtl_src_config script maps a simple text file containing a list of RTL source files to an ASE configuration file for simulation or an Intel Quartus Prime Pro configuration file for synthesis. rtl_src_config also defines preprocessor variables. Source configuration files may be hierarchical, with one file including another. rtl_src_config can construct ASE-based simulation trees or Quartus build trees.

Run rtl_src_config --help for a list of options and the required command syntax.

generate_ase_environment.py

The /ase/scripts/generate_ase_environment.py generates platform configuration files. afu_sim_setup invokes it automatically. A legacy mode in generate_ase_environment.py performs a brute-force check of the specified AFU RTL directories, attempting to define a compilation. This brute-force mode is imperfect and lists every file ending in .sv, .vs, .vhd, or .v and directories separated by +. It also may fail when compilation is order-dependent.

Run generate_ase_environment.py --help for a list of arguments.

  • The script requires a directory path to your RTL AFU.
  • -t: The default for the optional -t (tool) argument is VCS. For Mentor tools, use the QUESTA option.
  • -p: The default for the optional -p (platform) argument is intg_xeon which stands for the Integrated FPGA Platform. Use discrete for the Intel PAC.
  • -x: The optional exclusions argument lists exclusions for path searches.

The Synopsys and Mentor Graphics RTL simulators generate the following scripts.

  • Synopsys: Creates synopsys_sim.setup and vcs_run.tcl in the VCS configuration directory.
  • Mentor Graphics: Creates vsim_run.tcl in the QUESTA configuration directory.

The run-time simultation uses the .tcl files.

Details on generated files: * vlog_files.list: Lists all the Verilog and SystemVerilog files found in the AFU directory path. * vhdl_files.list: Lists all the VHDL files found in the AFU directory path. * ase_sources.mk: Ties the above two files into DUT_VLOG_SRC_LIST and DUT_VHD_SRC_LIST Makefile variables. * ASE_PLATFORM: Sets the platform type to the default type or the type you specify. * Set additional VCS or QUESTA options using the SNPS_{VLOGAN,VHDLAN,VCS}_OPT or MENT_{VLOG,VCOM,VSIM}_OPT options in the Makefile. Refer to ASE Makefile Variables for more information.

The simulation files use absolute paths when possible. To improve portability across users and groups, substitute environment variables in the generated files that build and run the simulator.

Note

You must manually check this file for correctness before using it in the simulation.

Cleaning the ASE Environment

Use the ASE cleanup script located in scripts/ipc_clean.py to kill zombie simulation processes and temporary files left behind by failed simulation processes or crashes.

$ ./ase/scripts/ipc_clean.py

############################################################
#                                                          #
#                ASE IPC Cleanup script                    #
#                                                          #
############################################################
IPC mounts seem to be readable... will attempt cleaning up IPC constructs by user ' user_foo '
Removing .ase_ready file ...
Type 'y' to clean up all zombie ase_simv processes : y
Going ahead with cleaning up ASE processes opened by  user_foo
$

ASE Usage

The AFU ASE is a server-client simulation environment. The AFU RTL is the server process. The software application compiled and linked to the OPAE ASE library is the client process. Communication between server and client uses named pipes. The ASE abstracts most of the simulation infrastructure. You do not need to modify it.

ASE
  • Server Process: * The server process interfaces to 3rd-Party RTL Simulator packages. The server process currently supports Mentor Modelsim-SE* Questasim* and Synopsys CS-MX* via the SystemVerilog-DPI library and simulator software interface. * Named pipes implement communication to the client. Named pipes also implement control, status and session management. The server process includes a pipe event monitoring engine. * SystemVerilog manages the CCI-P interface. All CCI-P events are logged and time stamped. * The server also includes a CCI-P protocol checker that checks CCI-P transactions originating in the AFU. This checker identifies CCI-P protocol issues, hazards, race conditions, and so on. * The buffer allocation calls map to POSIX Shared Memory (/dev/shm). The server-client processes share information about these buffers using named pipes.
The Physical addresses generated in ASE are not realistic and are not replicable in-system.
  • Client Process: * The client implements an OPAE interface and a library to access the ASE platform functionality including MMIO, Buffer management, and session control. The features available depend on the platform you specify at build time. These functions are available using the OPAE API. * The client process also provides a physical memory model that simulates the RTL AFU access to physical addresses. The physical memory model simulates address translation from virtual addresses to physical addresses. * A compiled program compiles and links to the ASE implementation of OPAE library. All OPAE calls route to ASE instead of the OPAE platform driver.

Separate build scripts build the server and client processes.

  • Server: A makefile in the ase directory compiles the ASE server process, containing the ASE Software, SystemVerilog engines and the AFU RTL logic code.
  • Client: The main cmake script in the root of the distribution builds the OPAE library implementations for the System and ASE. The cmake script installs the library in the lib directory.

AFU Build Instructions

ASE Application (Client) Build Instructions

Follow these instructions if you are building the OPAE SDK from a source tar file. Otherwise go directly to the Application build step.

Note

In these instructions, the directory /tmp/opae/ is the base directory where you install the OPAE API software distribution. The /tmp prefix may point to any system or user directory.

The ASE Source directory points to /tmp/opae/ase/

  • To build the OPAE libraries:
# Change directory to the opae directory
$ cd /tmp/opae/

# Check contents
$ ls
ase cmake common doc libopae platforms safe_string samples scripts tools AUTHORS CMakeLists.txt COPYING
README RELEASE_NOTES

# Create an out-of-build directory, and change to it
$ mkdir mybuild
$ cd mybuild

# Configure the software build using cmake (see options)
# $ cmake <Path to CMakeLists.txt>
# Install directory, in this example it is <Path  to opae>/myinst/

$ cmake ../ -DBUILD_ASE=YES -DCMAKE_INSTALL_PREFIX=/tmp/opae/myinst/
-- The C compiler identification is GNU 4.8.4
-- The CXX compiler identification is GNU 4.8.4
-- Check for working C compiler: /usr/bin/cc
-- Check for working C compiler: /usr/bin/cc -- works
.
.
.
-- Configuring done
-- Generating done
-- Build files have been written to: /tmp/opae/mybuild

# Build and install libraries
$ make
$ make install

# The environment Variable PATH should point to /myinst/bin
# Check library install paths
$ cd /tmp/opae/myinst/
$ ls
doc  include  lib

$ ls lib
libopae-c-ase.so  libopae-c.so  libopae-c.so.0  libopae-c.so.0.1.0 ...

Build the software application for the ASE using libopae-c-ase.so and the gcc command. You can build the software application using one of the following three methods:

Dynamically Linking libopae-c-ase.so
# Change directory to <Path to Directory>/opae/samples/
#   The UUID code requires the -luuid argument
#   Linking to the  ASE library requires the  -lopae-c-ase argument
#
$ gcc -g -o hello_fpga hello_fpga.c -L /tmp/opae/myinst/lib/ -I /tmp/opae/myinst/include/ -luuid -lpthread -lopae-c-ase -std=c99

# When running the application be sure the relevant LD_LIBRARY_PATH variable is set
$ ./hello_fpga
Dynamically Linking to the System Library and then Overriding It

The ASE implementation of the OPAE library simulates system behavior. Consequently, the application may also link dynamically to the System library, libopae-c.so and libopae-c-ase.so, and then override the system library with the LD_PRELOAD environment.

# Change directory to <Path to Directory>/opae/samples/
#   The UUID code requires the -luuid argument
#   Linking to the  ASE library requires the  -lopae-c-ase argument
#
$ gcc -g -o hello_fpga hello_fpga.c -L /tmp/opae/myinst/lib/ -I /tmp/opae/myinst/include/ -luuid -lpthread -lopae-c -std=c99

# When running the application be sure the relevant LD_LIBRARY_PATH variable is set
# You must also set the ASE_WORKDIR environment variable
$ LD_PRELOAD=libopae-c-ase.so ./hello_fpga
Compiling the libopae-c-ase.so Library with the OPAE Software Application

Use the OPAE ASE library implementation and compile it to the OPAE software application directly in one command using GCC.

  # Compile command
  $ gcc -g -o hello_fpga_ase hello_fpga.c /tmp/opae/myinst/lib/libopae-c-ase.so -I /tmp/opae/myinst/include/ -std=c99 -luuid

# When running the application, start the simulator, then set LD_LIBRARY_PATH and ASE_WORKDIR
$ ./hello_fpga_ase

ASE Simulator (Server) Build Instructions

ASE uses a platform differentiation key in the simulator Makefile to enable different platform features and produces a simulator configuration based on the differentiation key. These keys are set automatically by afu_sim_setup and generate_ase_environment.py.

You must note the following required build configurations:

Configuration Description Default
ASE_PLATFORM This is the platform differentiator . It must be set in ase_sources. mk to point to the required simulator features. FPGA_PLATF ORM_INTG_XEON` ` and ``FPGA_PLATFOR M_DISCRETE are the only legal values. FPGA_PLA TFORM_INTG _XEON
SIMULATOR This must be set in ase_sources. mk to point to the correct RTL simulator. VCS and QUESTA are the only legal values. VCS
DUT_VLOG_SRC_LI ST, DUT_VHDL_SRC_LI ST, and DUT_INCDIR These options point to AFU Verilog, VHDL and include path settings required for RTL simulators to build the simulation model correctly. None supplied — You must specify this.

For more information on other switches, refer to ASE Makefile targets

Use the scripts/generate_ase_environment.py script to generate the AFU-specific files for the simulator build. This script is not infallible and requires manual inspection of generated configurations to achieve correct results.

Note

Edit ase_sources.mk to add AFU RTL-specific define macros or include paths.

You may use the Generate ASE Environment script to generate the required AFU ase_sources.mk and vlog_files.list files.

# change to ASE directory
$ cd /tmp/opae/ase/

# Use the scripts/generate_ase_environment.py
$ ./scripts/generate_ase_environment.py -t VCS -p discrete <Path to sample RTL>
.
.
.
# Edit files as needed.

$ ls
ase_sources.mk  vcs_run.tcl  synopsys_sim.setup  vlog_files.list  ...

You may need to check vlog_files.list and ase_sources.mk files for correctness. Now, build the simulator with a ‘make’ command.

$ cd <opae>/ase/
$ make
.
.

$ ls work/ase_simv
work/ase_simv

ASE Runtime Instructions

The ASE server-client simulator makes the server before the client. Here are the run-time options:

$ make sim \
    [SIMULATOR=<VCS|QUESTA>] \
    [ASE_CONFIG=<Path to ase.cfg>] \
    [ASE_SCRIPT=<Path to ase_regress.sh if ASE_MODE=4>]

Use two terminal windows to start the simulation.

  • Terminal 1: Runs make sim. The ASE initializes and the AFU issues a reset and then waits for incoming transactions. The software application must wait until the “Ready for Simulation” message displays.

Specify the environment variable ASE_WORKDIR Terminal 1.

# Invoke the simulator
$ make sim
SIMULATOR=VCS
CC=gcc
#################################################################
#                                                               #
#             OPAE Intel(R) Xeon(R) + FPGA Library              #
#               AFU Simulation Environment (ASE)                #
#                                                               #
#################################################################
ASE platform set to MCP_SKYLAKE mode
.
.
.
SIM-SV: Transaction Logger started
SIM-SV: Simulator started...
SIM-C : +CONFIG /tmp/opae/ase/ase.cfg file found !
SIM-C : +SCRIPT /tmp/opae/ase/ase_regress.sh file found !
SIM-C : PID of simulator is 41819
SIM-C : Reading /tmp/opae/ase/ase.cfg configuration file
SIM-C : ASE was started in Mode 1 (Server-Client without SIMKILL)
        ASE mode                   ... Server-Client mode without SIMKILL
        Inactivity kill-switch     ... DISABLED
        Reuse simulation seed      ... ENABLED
        ASE Seed                   ... 1234
        ASE Transaction view       ... ENABLED
        User Clock Frequency       ... 312.500000 MHz, T_uclk = 3200 ps
        Amount of physical memory  ... 128 GB

.
.
.
SIM-C : ** ATTENTION : BEFORE running the software application **
    Set env(ASE_WORKDIR) in the terminal where application will run (copy-and-paste) =>
    $SHELL   | Run:
    ---------|---------------------------------------------------
    bash/zsh | export ASE_WORKDIR=/tmp/opae/ase/work
    tcsh/csh | setenv ASE_WORKDIR /tmp/opae/ase/work
    For any other $SHELL, consult your Linux administrator

    SIM-C : Ready for simulation...
    SIM-C : Press CTRL-C to close simulator...

You can close Terminal 1 make simby issuing a SIGTERM to the relevant ase_simv process or by typing CTRL-C.

  • Terminal: First set the environment variable ASE_WORKDIR as specified in Terminal 1. In this example ASE_WORKDIR is set to /tmp/opae/ase/work. Then, start the software application.
# Set ASE_WORKDIR environment variable
$ export ASE_WORKDIR=/tmp/opae/ase/work/

# Run the application
$ export LD_LIBRARY_PATH=/tmp/opae/myinst/lib/
$ LD_PRELOAD=libopae-c-ase.so ./hello_fpga

Note

After the application exits, the simulation is complete. Close the simulator to allow the waveform dump process to complete. In Terminal 1, type the CTRL-C command.

<Simulator running>
.
.
.
SIM-C : Ready to run next test
818602500C0Tx AlmFull toggled from 1 to 0

818602500C1Tx AlmFull toggled from 1 to 0

<CTRL-C Key hit>

^CSIM-C : Closing message queue and unlinking...
SIM-C : Unlinking Shared memory regions....
SIM-C : Session code file removed
SIM-C : Removing message queues and buffer handles ...
SIM-C : Cleaning session files...
SIM-C : Simulation generated log files
    Transactions file       | $ASE_WORKDIR/ccip_transactions.tsv
    Workspaces info         | $ASE_WORKDIR/workspace_info.log
    ASE seed                | $ASE_WORKDIR/ase_seed.txt

SIM-C : Tests run     => 1
SIM-C : Sending kill command...
SIM-SV: Simulation kill command received...

Transaction count |       VA      VL0      VH0      VH1 |    MCL-1    MCL-2    MCL-4
========================================================================================
MMIOWrReq           9 |
MMIORdReq           2 |
MMIORdRsp           2 |
UMsgHint            0 |
UMsgData            0 |
RdReq           16384 |        0        0    16384        0 |    16384        0        0
RdResp          16384 |        0        0    16384        0 |
WrReq           16385 |        0        0    16385        0 |    16385        0        0
WrResp          16385 |        0        0    16385        0 |    16385        0        0
WrFence             1 |        0        0        1        0 |
WrFenRsp            1 |        0        0        1        0 |

$finish called from file "/tmp/opae/ase/rtl/ccip_emulator.sv", line 2657.
$finish at simulation time           1514962500
V C S   S i m u l a t i o n   R e p o r t
Time: 1514962500 ps
CPU Time:    142.500 seconds;       Data structure size:   1.1Mb
Tue Jun 20 13:29:13 2017

Upon completion, the simulation generates the following files:

  • Waveform dump: make wave opens the waveform for the selected tool.

    * ```inter.vpd```: VCS Waveform file
    * ```vsim.wlf```: Mentor/Questa waveform file.
    
  • $ASE_WORKDIR/ccip_transactions.tsv: CCI-P Events log listing all events observed on the CCI-P interface. The timestamps indicate the corresponding time interval in the waveform dump VPD file.

  • $ASE_WORKDIR/workspace_info.log: Information about buffers the simulation opened.

  • $ASE_WORKDIR/ase_seed.txt: Information about the simulation seed.

  • $ASE_WORKDIR/ccip_warnings_and_errors.txt: Information about CCI-P warnings and errors.

Recommendations

  1. The ASE ccip_logger.sv module logs CCI-P events for designs that use the CCI-P protocol. This module allows you to compare transactions and traffic flow through the CCI-P interfaces.

Note

Use a different file name for each instantiation of the of the ccip_logger.

ASE
  1. The ASE shutdowns simulations gracefully, closing all mutexes, locks, POSIX structures safely before exiting via the $finish statement in SystemVerilog. If your AFU design uses $error or $finish to identify error conditions while simulating, consider using the handle start_simkill_countdown() instead. start_simkill_countdown() calls $finish after completing the steps for a graceful shutdown.
  2. You can script ASE simulations. When the simulator is ready for use, the simulation writes a lock file, $ASE_WORKDIR/.ase_ready, to the work directory.
# Start Simulator in background
make sim &

# Wait for simulator readiness
# When .ase_ready is available in the $ASE_WORKDIR, the ASE is ready for simulation
while [ ! -f $ASE_WORKDIR/.ase_ready.pid ]
do
    sleep 1
done

# Start application
cd $PATH_TO_APPLICATION

# Export ASE_WORKDIR variable
export ASE_WORKDIR={Path to simulator mentioned in ASE green printout}
./Application
  1. To reduce simulation time, make the following changes to the default simulation settings: * Turn OFF wave dumps: Check your RTL vendor’s recommendation on switching off wave form dumps. In some cases, is possible to generate wave dumps for specific module hierarchies. * Turn OFF display messages by setting ENABLE_CL_VIEW = 0 in ase.cfg.
  2. To generate random CCI-P transactions for every run, modify the ASE latency model, $ASE_SRCDIR/rtl/platform.vh. The *_LATRANGE constraint defines a min/max pair:
`define X_LATRANGE     min, max

The min and max values are the minimum and maximum cycle counts for responses returning to the AFU. Simulation assigns transactions a random latency in the (min, max) range. The larger the difference between (min, max), the larger the standard deviation of latency for a given type of transaction. You can specify different (min, max) values for different transaction types.

Note

The latency values specified for simulation are for testing only. They may not accurately represent the real latencies of your system hardware.

/*
 * Latency model
 * Coded as a Min,Max tuple
 * -------------------------------------------------------
 * RDLINE_LATRANGE : ReadLine turnaround time
 * WRLINE_LATRANGE : WriteLine turnaround time
 * UMSG_LATRANGE   : UMsg latency
 * INTR_LATRANGE   : Interrupt turnaround time
 *
 * LAT_UNDEFINED   : Undefined latency
 *
 */
`define MMIO_LATENCY                15
`define RDLINE_S_LATRANGE          20,118
`define RDLINE_I_LATRANGE          20,118
`define WRLINE_M_LATRANGE          20,118
`define WRLINE_I_LATRANGE          20,118
`define UMSG_START2HINT_LATRANGE   39,41
`define UMSG_HINT2DATA_LATRANGE    41,45
`define UMSG_START2DATA_LATRANGE   82,85
`define INTR_LATRANGE              10,15

`define LAT_UNDEFINED              300

`define RDWR_VL_LATRANGE           20,118
`define RDWR_VH_LATRANGE           140,180

`define ASE_MAX_LATENCY            300
  1. The ASE includes a CCI-P protocol checker, $ASE_SRCDIR/rtl/ccip_checker.sv. Use this module to verify CCI-P compliance. The checker sniffs transactions, conditions and header settings and flags warnings or errors. Identify multiple issue classes in the hw/ccip_sniffer.sv. The ASE logs all warnings and errors in $ASE_WORKDIR/ccip_warnings_and_errors.txt.
ASE
  • Memory errors in transactions: Memory errors have the highest severity. The simulation stops immediately. The ASE logs memory errors, including timestamps, in $ASE_WORKDIR/ase_memory_error.log.
  • Protocol warnings: Warnings do not stop the simulation. The ASE logs warnings in $ASE_WORKDIR/ccip_warning_and_errors.txt.
  • The ASE may also log memory hazards (RAW, WAR and WAW hazards).

ASE Example

A tutorial for CCI-P systems is available in a separate Basic Building Blocks repository in the samples/tutorial tree. The first example, 01_hello_world follows the afu_sim_setup flow described above. Start with the tutorial’s README file for configuration and execution instructions. The example defines a set of sources and walks through the process of creating an ASE tree, running the simulator and connecting it to a host program.

Operation Reference

ASE Simulator Makefile Switches

The ASE Makefile template comprises many targets and switches. Build your own compilation script for more complex simulations.

For a complete listing including the versions supported, see System Requirements section.

ASE Makefile Build Flow

Complete the following steps to compile ASE Simulator:

  1. Compile Software objects of ASE into a library file *First compile the Software components located in the ase/sw/ directory into a software library.

Note

Define SIM_SIDE as a compilation macro when compiling the ASE simulator objects. The SIM_SIDE switch is for simulation software, not the OPAE ASE software library.

  1. Compile The ASE SystemVerilog files located in the ase/rtl/ directory. Compile ASE RTL the platform components for the Integrated FPGA Platform or the Intel PAC into the simulation databases. For the PAC, compile the embedded memory interface (EMIF) Memory controller model into the ASE environment. If the simulation requires the Intel FPGA Gate libraries, compile the models into the ASE environment.
  2. Compile AFU components into the ASE environment. Use the RTL simulator software tools to compile the AFU components. Use Synopsys or Mentor utilities to compile VHDL or SystemVerilog components.

ASE Makefile Targets

Target Description
all Default build target, builds a simulator in Synopsys VCS-MX
header Print version and preamble
check Environment check
sw_build Build ase/sw/ components into a software library. The SIM_SIDE switch builds the simulator software components
help Print help information
vcs_build Synopsys VCS-MX template build flow
questa_build Mentor Graphics Modelsim-SE/Qu estaSim template build flow
sim Start the ASE Simulator
wave Open selected RTL waveform viewer
clean Clean build, simulation, and log files
distclean Clean distribution - removes the AFU configuration files

ASE Makefile Variables

Makefile target Description Default value
VCS_HOME Synopsys VCS-MX installation path Installation tool specific
MTI_HOME Mentor installation path Installation tool specific
QUARTUS_HOME Intel Quartus Prime Pro installation path Installation tool specific
ASE_PLATFORM Platform selection switch: Specify either tightly-couple d FPGA or programmable FPGA acceleration card using FPGA_PLATFOR M_INTG_XEON and FPGA_PLATFOR M_DISCRETE, respectively FPGA_PLATFORM_ INTG_XEON
SIMULATOR Simulator Key to environment Defined values VCS or QUESTA VCS
ASE_SRCDIR ASE source location Current source path
ASE_WORKDIR Location where ASE runs, usually $ASE_SRCDIR/ work Environment-spec ific execution path
WORK Simulation library compilation location work
``ASE_DISABLE_LOGGER` ` Switch to disable logger build 0
``ASE_DISABLE_CHECKER `` Switch to disable checker build WARNING: Disabling this checker may have side effects on protocol correctness 0
GLS_SIM Enable gate simulation build 1
GLS_VERILOG_OPT Libraries that enable Intel gate simulation Quartus EDA simulation library paths
ASE_CONFIG ASE Run-time configuration file (described `here <#ase-ru ntime-configur ation-options> `__) $ASE_SRCDIR/as e.cfg
ASE_SCRIPT ASE Regression script path $ASE_SRCDIR/as e_regress.sh
TIMESCALE Simulator timescale 1ps/1ps
ASEHW_FILE_LIST ASE RTL File list Refer to ase/Makefile
ASE_MEM_FILE_LIST ASE RTL file list for programmable FPGA acceleration card mode memory Refer to ase/Makefile
ASE_INCDIR ASE Include directory paths Refer to ase/Makefile
ASE_TOP ASE top level entity (must not be changed) ase_top
CC_OPT ASE Software Library compiler build options

``-g -m64 -fPIC -D SIM_SIDE=1 -I

$(ASE_SRCDIR)/s

w/ -D SIMULATOR= VCS -D $(ASE_PLA TFORM) -Wall -I $(VCS_HOME)/incl ude/``

ASE_LD_SWITCHES ASE Software Linker switches
``-lrt -lpthread
-lstdc++ -luuid

``

SNPS_VHDLAN_OPT Synopsys VCS-MX VHDL compile options (add extra options to ase_sources. mk) Refer to ase/Makefile
SNPS_VLOGAN_OPT Synopsys VCS-MX SystemVerilog compile options (add extra options to ase_sources. mk) Refer to ase/Makefile
SNPS_VCS_OPT Synopsys VCS-MX options for building simulator executable (add extra options to ase_sources. mk) Refer to ase/Makefile
SNPS_SIM_OPT Synopsys VCS-MX Simulation options (add extra options may to ase_sources. mk) Refer to ase/Makefile
MENT_VCOM_OPT Mentor Modelsim-SE/Qu estasim VHDL compile options (add extra options to ase_sources. mk) Refer to ase/Makefile
MENT_VLOG_OPT Mentor Modelsim-SE/Qu estasim {System}Verilo g compile options (add extra options to ase_sources. mk) Refer to ase/Makefile
MENT_VSIM_OPT Mentor Modelsim-SE/Qu estasim VHDL simulation options (add extra options to ase_sources. mk) Refer to ase/Makefile
DUT_VLOG_SRC_LIST Points to a text file listing AFU {System}Verilo g files (usually vlog_files.l ist) User generated
DUT_VHDL_SRC_LIST Points to a text file listing AFU VHDL files (usually vhdl_files.l ist User generated
DUT_INCDIR Lists AFU include directories separated by a ‘+’ (usually in ase_sources. mk) User generated

ASE Runtime Configuration Options

The ASE configuration file configures simulator behavior. An example configuration script is available at ase/ase.cfg

Switch Name Default Description
ASE_MODE 1 ASE mode has the following valid values: 1 : Standard Server-Clien t Mode2 : Simulator stops after ASE_TIMEOU T clocks3 : Software shuts down simulator when client application releases session 4 : Regression mode invoked by script>=5 : Ignored (revert to ``ASE_MODE=1 ``)
ASE_TIMEOUT 50000 (only if ASE_MODE=2) Watchdog timer shuts down simulator after ASE_TIMEOU T clocks of CCI-P interface inactivity.
ASE_NUM_TESTS 500 (only if ASE_MODE=4) Number of tests in regression mode. If incorrectly set, the simulator may exit pre-maturely or stall waiting for tests to get started.
ENABLE_REUSE_D 1 When set to 1, reuses the simulation seed, so that CCI-P transactions replay with the previous addresses. When set to 0, obtains a new seed.
ASE_SEED 1234 (only if ENABLE_REUSE_SEED=1) ASE seed setting, enabled when ENABLE_REU SE_SEED is set to 1, otherwise the simulations uses a different seed. At the end of the simulation, the ASE writes the current seed to $ASE_WORKD IR/ase_seed. txt.
ENABLE_CL_VIEW 1 The ASE prints all CCI-P transactions . On long simulation runs, setting ENABLE_CL_ VIEW to 0 may reduce simulation time.
PHYS_MEMORY_AVAILABLE_ GB 32 Restricts ASE address generation the specified memory range.

Logging Verbosity Control

ASE provides the following three levels for logging message verbosity. By default, these messages print to stdout:

  • ASE_INFO: Prints mandatory information messages required to specify operation.
  • ASE_ERR: Prints error messages during operation.
  • ASE_MSG: Prints general messages indicating check points in the ASE. Suppress these messages by setting the environment variable ASE_LOG to 0.

The following command suppresses the ASE_MSG category:

$ ASE_LOG=0 LD_PRELOAD=libopae-c-ase ./hello_fpga

You cannot suppress warnings and errors.

Troubleshooting and Error Reference

The following list of ASE errors and warnings is not comprehensive:

Observation Problem Next Steps
Either all transactions are not seen or simulation ends earlier than expected. ASE Simulation inactivity is too short for the application use-case to be successfully simulated in the ASE. If using ASE_MODE=2 (Daemon with timeout), in the ase.cfg file, increase the ASE_TIMEOUT setting or disable ASE_TIMEOUT.
ASE simulation build error - compilation, or linking failed GCC version might be too old. In the ase directory try the following command $ make sw_build ASE builds correctly with GCC 4.8.5 or higher. Use the ase/scripts/env_check .sh script to identify issues.
Synopsys VCS-MX dumped stack while compiling or running Possible corruption of compiled objects or problems with incremental compilation.

Clean the ASE environment using $ make clean If this command fails, clean the distribution with $ ./distclean.sh

then

rebuild the simulation.

ERROR: Too many open files Past ASE simulation runs did not close cleanly and may have left behind open IPC instances. Use the $ASE_SRCDIR/scripts/i pc_clean.py script to clean IPC instances. Check if the System Requirements have been met. If problems continue, increase resource limits for your Linux distribution.
$ASE_WORKDIR environment variable has not been set up Application cannot find a valid simulation session Follow the steps printed when the ASE simulation starts. These instructions are in green text.
.ase_timestamp cannot be opened at <DIRECTORY> Simulator may not have been started yet. Note that when started, the simulator prints: Ready for Simulation$ASE_W ORKDIR may not set up correctly. Check the ASE_WORKDIR environment variable. ``$ echo $ASE_WORKDIR `` Wait for simulator to print: ``Ready for Simulation` `
ase_sources.mk: No such fi le or directory ASE Environment has not been generated. Generate an AFU RTL listing (in vlog_files.list and ase_sources.mk) configuration. You can use ase/scripts/generate_ ase_environment.pyt o generate these files.
An ASE instance is probably still running in current directory. An ASE simulation is already running in the $ASE_WORKDIR directory. If the simulation process is unusable or unreachable, use the ase/scripts/ipc_clean .py script to clean the simulation temporary files using: $ make clean. Then rebuild the simulator.

Revision History

Document Version Intel Acceleration Stack Version Changes
2018.04.16 1.1 Alpha. (Supported with Intel Quartus Prime Pro Edition 17.1.1.) Made the following changes: * Added afu_sim_s etup script which reads a file containing a list of RTL sources and constructs an ASE tree to compile and simulate. * Added /platform s/scripts/r tl_src_conf ig script which maps a simple text file containing a list of RTL source files to an ASE configurati on. * Updated figures to show the hardware available in the Intel PAC with Arria® 10 GX FPGA.